產品描述
(共4頁-當前第1頁)
進口杠桿浮球式疏水閥
LEVER-BALL FLOAT TRAP
進口杠桿浮球式疏水閥
德國萊克(LIK)杠桿浮球式是利用浮力原理和杠桿原理,通過液位的變化使浮球上升或下降,浮球驅動著杠桿使得閥瓣離開或接觸閥座達到開啟排水和關閉阻汽的作用。采用自動排空氣閥,能自動排除不凝結氣體,非常靈敏,工作質量高,使用壽命長。連續排水,有水即排,最小過冷度為 0℃。杠桿浮球式疏水閥采用兩種結構方式 A:?jiǎn)伍y座-杠桿浮球; B:雙平衡閥座-杠桿浮球。
單閥座:需要克服介質壓力對閥座的作用,閥座的孔徑不能很大,適用于小型設備、伴熱管線,蒸汽主管等排水小的場合。閥座孔設計在凝結水水位以下,自然形成水封,水、汽自然分離,達到無蒸汽泄漏,即便沒有凝結水采用球型密封的杠桿使得閥瓣緊貼閥座,達到無新鮮蒸汽的泄漏。不受凝結水量波動和溫度的影響。
雙平衡閥座:該閥利用雙閥孔設計,介質的壓力對兩個閥座作用相等,方向相反,介質壓力對閥座作用相抵消,閥芯在開閥時壓力相對減少,從而獲得超大排量。工作時浮球隨閥腔內液體位的變化而上下浮動,帶動杠桿打開或關閉閥座。由于閥座孔在凝結水水位以下,形成水封,水、汽自然分離,達到無蒸汽泄漏。不受壓力、溫度、冷凝水流量波動的影響。
Lever-ball float trap
The lever-ball float type trap employs the buoyancy and leverage principles: to make the ball float ascend or descend by the change in the liquid level and then the ball float drives the lever to make the valve disc depart from or touch the valve seat to realize drainage and close the block vapor. The product adopts the automatic air exhaust to automatically eliminate non-condensing air. It is very precise with high operating quality and long service life. It can discharge whenever there is any water, and its minimum subcooled temperature is 0℃. The lever- ball float trap adopts two kinds of structure modes: A: Single valve seat-lever ball float; B: double balanced valve seat-lever ball float.
Single valve seat: it needs to overcome the operation on the valve seat by the medium pressure; the hole caliber of the valve seat cannot be too large and is applicable to such low displacement condition as mini-equipment, steam tracing pipeline and steam main pipe. The hole of the valve seat is designed beneath the water level of the condensate water to form water sealing to keep water apart from vapor, so as to prevent the leakage of the vapor. Though there is no condensate water that uses ball-type sealed lever to make the valve clack tightly adhesion to the valve seat, it can prevent the fresh vapor from leakage. Further, the product is free of the affect of the fluctuation of the condensate water’s quantity and temperature.
The double balanced valve seat: this valve is designed to have two valve openings. The pressure of the medium act against the two valve seats equally in reverse direction, so the pressure on the valve seat is offset, the valve core assumes relatively low pressure when the valve is open, in this way the overlarge displacement is obtained. During the operating process, the ball float floats with the change in liquid level of the valve cavity to make the lever open or close the valve seat. The hole of the valve seat is designed beneath the water level of the condensate water to form water sealing to keep water apart from vapor, so as to prevent the leakage of the vapor. Further, the product is free of the affect caused by the fluctuation of pressure, temperature and condensate’s flow.
優點:
1、采用新型閥機構(新 SCCV 關閉方式和Z型結構),具有優良的密封性和耐久性。
2、雙平衡閥座設計,比一般的疏水閥體積小而排量大,在特大排量場合更能發揮優越性。
3、單閥座設計可以水平或垂直安裝,可以滿足高背壓,低排量蒸汽管線。
4、內裝空氣自動排放閥,可防止空氣氣堵和蒸汽汽鎖。
5、全部部件安裝在閥蓋上,閥無需從配管上卸下,就可維修保養,簡單方便。
Merits
1. To use new-style valve mechanism (new SCCV closing mode and Z-shaped structure) to boast excellent tightness and endurance.
2. To employ double balanced valve seat design, it has smaller volume and larger displacement and can exert its advantages when needing large displacement.
3. The single valve seat model can be installed horizontally and vertically, satisfying the requirements of steam pipeline with high backpressure and low displacement.
4. The built-in automatic air exhaust can prevent air blocking and steam locking;
5. As all components are installed on the valve cover, so they can be maintained and cleaned up simply and easily without being removed from pipe arrangement.
技術參數/Technique parameter
|
殼體壓力等級
Shell pressure grade
|
負荷泄漏率
Load leakage rate
|
使用介質
Used medium
|
允許背壓率
Permitted backpressure rate
|
節能效果
Energy saving effect
|
最大工作壓差
Maximum operating pressure differential
|
|
1.6、2.5、4.0、10MPA
|
≈0%
|
蒸汽、凝結水
Steam、Condensate water
|
≥90%
|
優秀/良好
Excellence/good
|
10MPA
|
|
最小過冷度
Minimum subcooled temperature
|
排水方式
Drainage method
|
最高允許溫度
Maximum allowable temperature
|
排空氣裝置
Air exhaust system
|
壓力變化范圍
Pressure change range
|
|
0℃
|
連續方式
Continue mode
|
420℃
|
自動
Automatic
|
適應
Adaption
|
主要零件材料/The materials of primary accessories
|
零部件名稱Part and component name
|
材質Material
|
|
閥體、閥蓋Valve body、Valve cover
|
鑄鋼、不銹鋼Cast steel、Stainless steel
|
|
浮球、杠桿Float ball、Lever
|
304不銹鋼304 Stainless steel
|
|
雙平衡閥座Dual balance valve seat
|
STL合金和不銹鋼組合Combination of STL alloy and stainless steel
|
|
自動排空氣裝置Automatic air exhaust
|
不銹鋼、熱敏元件Stainless steel、Thermo-sensitive element
|
|
過濾網Filtrating screen
|
不銹鋼Stainless steel
|
德國萊克(LIK)閥門重視客戶提出的每一個要求,并按照客戶提出的要求量身定做,力求為客戶提供最好的解決方案,同時也能優化產品性能,客戶感到很滿意且與他們保持緊密的合作關系。我們堅持這樣做并取得了成功,這是我們發展的動力。自從德國萊克(LIK-VALVE)閥門誕生的那一刻起,我們就繼承了德國傳統的苛刻的制造精神,我們力求每一個環節都做到精益求精,所以我們的質保系統滲透到每一個工序,確保每個工人用到的是最好的零配件,這是我們發展的根本。
基于萊克(LIK)閥門業務在中國的發展和壯大,萊克集團于2000年在廣州設立了第一個辦事處,同年在香港設立亞洲總部-萊克集團亞洲有限公司。2000年設立了廣州分公司,為國內客戶提供更方便快捷的服務。同時萊克集團在中國的員工全部需要不定期的送到德國總部進行培訓,因此他們能夠運用先進的技術為國內客戶提供高品質的服務。
一直以來,為用戶量身定做,提供我們最有競爭力的萊克(LIK)閥門解決方案是我們的目的和行動指南。我們長期關注市場并貼近客戶,您完全可以信賴我們?nèi)R克(LIK)閥門品牌,及其專業的技術服務團隊。我們的戰略是集中全球優勢滿足當?shù)乜蛻舻男枨蟆?/div>
我們相信萊克(LIK)閥門能夠?yàn)榭蛻籼峁┳詈玫膬r(jià)值!
德國萊克要產品有:進口調節閥、進口蝶閥、進口截止閥、進口球閥、進口止回閥、進口閘閥、進口疏水閥、進口旋塞閥、進口水力控制閥、進口電磁閥、進口平衡閥、進口過濾器、進口阻火器、進口呼吸閥、進口保溫閥門、等
代理商 服務中心 了解萊克 聯系我們 客戶采購指南
進入德國萊克網站了解更多信息http://www.aocunvalve.com
聯系我們
銷售電話:020-61139066 61132877 (孫先生)| 傳真:32398971
|技術部:020-32399500 (王先生)Email:leovalve@126,com
(1)網址http://www.likvalve.com
(2)公司網址http://www.aocunvalve.com
(3)公司網址http://www.020valve.com
(4)公司網址http://www.gzfm.cn/
(5)公司網址http://www.gzjkfm.com/
(6)公司網址http://www.86pv.net/